X-440 Penetrating Water Based Concrete, Masonry Sealer and Water Repellent. 5 Gal. Pail

$189.99

Vital Coat X-440 sealer is a high performance, high solids water based low VOC Silane Siloxane penetrating sealer and water repellent for concrete and masonry surfaces. It penetrates deep into the surface and chemically reacts with the concrete to create a protective hydrophobic water repellent barrier yielding a longer lasting protection against water intrusion, salts, staining, freeze/thaw, mold and mildew, efflorescence, dusting, scaling and spalling. X-440 is a non-yellowing, UV resistant sealer that does not leave behind a visible surface film, and will not change the look or color of the surface. It will preserve the natural characteristics of the treated substrates.

 

In stock

Description

X-440 Penetrating Sealer can be applied to residential and commercial, interior or exterior, horizontal or vertical structures. It protects concrete and masonry surfaces including architectural concrete, concrete block, split-face block, pavers, stucco, porous and dense brick, clay tile, etc. It is also an excellent choice for high-traffic areas because it does not create a slippery film on top of the surface. X-440 helps protect your concrete and masonry surfaces to resist common issues such as staining, cracking, spalling, efflorescence, and other damages caused by intrusion of water.
Product Benefits

  • Environmentally friendly, nontoxic and nonflammable
  • Resistant to UV rays
  • Does not turn yellow over time
  • Permanently seals and protects concrete, brick and other hard surfaces.
  • Does not peel or flake over time
  • Provides long-term cost savings by preventing the need for frequent concrete maintenance, repair costs and reapplications
  • Protects against salts, acids, oil, grease, moisture, mold and mildew
  • Prevents the deterioration of your concrete that typically occurs after freezing and thawing as the seasons change
  • X-440 Benefits
  • Provides superior water repellency, while allowing surface to breathe
  • Does not change the appearance of the substrate
  • No slippery film is formed on the substrate
  • Works on new or existing structures
  • Provides a protective hydrophobic barrier to prevent water penetration
  • Reduces deterioration from spalling and pitting because of exposure to salts and chlorides
  • Will Preserve the natural, unsealed look and feel of the substrate
  • Efflorescence and strong alkali resistance
  • Water Based and VOC Compliant
  • Long Lasting up to 5 Years
  • Reduces chloride penetration
  • UV resistant
  • Alkali resistant
  • Freeze/Thaw/De-icing salt resistant
  • Provides excellent resistance to mold, mildew, and fungus
  • Reduces dirt pick-up

Recommended Uses

  • Concrete Pavers
  • Brick Pavers
  • Block Walls
  • Chimneys
  • Natural Stone
  • Driveways
  • Patios
  • Garage Floors
  • Pool Decking
  • Retaining Walls
  • Warehouse Floors
  • Stucco
  • Aggregate
  • Mortar and Grout

 

Additional information

Weight 44 lbs
Dimensions 12 × 12 × 15 in
Product Name Type Of Surface Coverage Size of Area (sq ft) Recommended Amount
X-440 Penetrating Water Based Concrete, Masonry Sealer and Water Repellent. 5 Gal. Pail Rough Concrete 125 to 200sq. ft. per gallon

Application

General Instructions.

Before using this product read the Technical Data Sheet (TDS) and the Safety Data Sheet (SDS)

found at www.vitalcoat.com.  Apply in temperatures between 40°F – 90°F (4°C – 32°C). Always tighten lid thoroughly after use. Always perform a test application for proper penetration on each type of surface prior to full-scale application to determine suitability and final appearance. Test using the recommended application instructions. Let area dry thoroughly before inspection.

 

General Surface Preparation

Surface preparation is important. Surfaces must be structurally sound, clean and free from as much dirt, stains, efflorescence, oil, and other contamination as possible.  Protect people, vehicles, property, plants, and all surfaces from exposure to the product, from splash, residue, and wind drift before application. Do not mix or add any other chemical to this product. Insure that surface is thoroughly dried before application. Excessive moisture inhibits sealer penetration. A small test must be conducted prior to application. Based upon this test, the purchaser shall determine for themselves the suitability of this product for the intended use. Allow 14 – 28 days for new concrete or masonry to cure before applying X-440.

 

Application

X-440 can be sprayed, brushed or rolled. For best results, using a quality sprayer capable of a producing a steady pressure under 40 psi. A .1 – .2 GPM tip is recommended. Completely saturate the surface ensuring that the entire surface is saturated. Do not let the product puddle on the surface or dry on the surface. Back roll with a brush or a medium nap paint roller. DO NOT OVERAPPLY. Let dry for 10 to 15 minutes. If second coat is needed, apply wet-on-wet. On highly permeable surfaces, additional coats may be necessary. On vertical applications, apply from the bottom up. Protect surfaces from rainfall for six hours following treatment. Many surfaces need several days to develop optimum water repellency. Immediately clean tools, equipment, and overspray with soap and warm water.

 

Precautions

Do not alter or add any other chemical to the product. Do not dilute unless specified in the Technical Data Sheets. Do not allow to freeze. Mix well before using. X-440 will not hide existing surface stains. Temporary darkening of some substrates may occur. Do not apply if rain is expected within 24 hours. Protect treated surfaces from rainfall for a minimum of six hours following treatment. Not intended for use on surfaces that will be constantly be submerged in water.

Technical

Technical

Safety Data Sheet
Technical Data Sheet

Reviews

There are no reviews yet.

Be the first to review “X-440 Penetrating Water Based Concrete, Masonry Sealer and Water Repellent. 5 Gal. Pail”

Your email address will not be published. Required fields are marked *